Iai-america RCB-101-MW Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Iai-america RCB-101-MW. IAI America RCB-101-MW User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir

Indice de contenidos

Pagina 1 - Operating Manual

RCB-101-MWPC Software Operating Manual 9th Edition

Pagina 2 - Software License Agreement

5 3. Main Window Fig. 3.1 Main Window You can select the following items from the main menu or toolbar available i

Pagina 3 - Supported Models

6 [5] [Backup] (Available in the online mode) [Save from Controller to File] Save all position data and parameters in the controller to a fi

Pagina 4 - A Word of Caution

7 [2] [Controller Setup] Reconnect: Reconnect the axes. If the software connects to multiple controllers linked by controller link cables, al

Pagina 5 - Table of Contents

8 3-2 Operations Using the Toolbar Buttons Fig. 3.2 Toolbar Buttons [1] New position data Same as clicking File, pointing to New, a

Pagina 6 - 1. Before You Begin

9 Fig. 3.3 Toolbar Buttons [1] Cascade windows Same as clicking Window, and then selecting Cascade. [2] Tile windows vertically Same as c

Pagina 7 - 1-4 Starting the Software

10 [2] Position data You can double-click this item to open the position data edit window. [3] Parameter You can double-click this item to open

Pagina 8

11 4. Selecting an Axis To perform any of the following operations, select the axis number of the target axis in the “Select axis number” windo

Pagina 9

12 5. Editing Position Data You can edit position data in the online or offline mode. 5-1 Online Mode In this mode, data can be loaded fro

Pagina 10 - 3. Main Window

13 The operating methods of buttons and input controls available in this window are explained below. (1) Toolbar buttons Fig. 5.2 Toolb

Pagina 11

14 [8] Switch display Change the display mode of the position data input area from normal to detail (or vice versa). (Fig. 5.14, Fig. 5.15) [9]

Pagina 12

Software License AgreementBefore opening this product, read the software license agreement (hereinafter referred to as “Agreement”). This Agreement ap

Pagina 13

15 The input fields of position data generated by the equal division function, other than Position and Comment, will be populated by the correspond

Pagina 14 - 3-3 Tree View

16 (2) Current position/alarm code The current position of the axis you are editing (unit: mm) and the associated alarm code, if any, are shown.

Pagina 15 - 3-4 Status Bar

17 Clicking (step) will move the axis by one position, while clicking (continuous move) will cause the axis to move continuously by loopi

Pagina 16 - 4. Selecting an Axis

18 Checkbox: The axes with a check mark in this box will move. The selectable checkboxes are those of axes whose point edit window is currently op

Pagina 17 - 5. Editing Position Data

19 (5) Program Just like positioning, this is also a test operation mode. In the program mode, however, you can set a desired sequence of movement

Pagina 18

20 [3] Alarm button This button lets you reset an alarm. Note that an alarm can be reset only when the servo is off and the cause of the ala

Pagina 19

21 5-2 Offline Mode When editing data after creating new data or loading data from a file, you are editing the data in the offline mode. In this

Pagina 20

22 6. Editing Parameters To load parameter data from the controller, click Parameter and then select Edit from the main menu, or click i

Pagina 21

23 Depending on the controller model, a confirmation window (Fig. 6.2) may be displayed after parameters have been sent to the controller, asking i

Pagina 22

24 7. Monitoring You can monitor various statuses, controller error list, and velocity/current waveforms (only if the controller supports the func

Pagina 23 - Position

Supported Models The PC software RCB-101-MW supports the following controller models of the specified versions and later. Table 1 List o

Pagina 24

25 7-2 Controller Error List To monitor the controller error list, click Monitor and then select CTR Error List from the main menu, or click

Pagina 25

26 7-3 Velocity/Current Monitor Window To monitor velocity/current, click Monitor and then select CTR Error List from the main menu, or click

Pagina 26 - 5-2 Offline Mode

27 (3) Toolbar Fig. 7.5 Toolbar [1] Save as Save the displayed current data and velocity data to a file (CSV format). * Only the ra

Pagina 27 - 6. Editing Parameters

28 7-4 Setting of Application Window Click Setup from the main menu, and then select Application Setup. Fig. 7.6

Pagina 28

29 * The change will become effective once the application is restarted or the axes are reconnected. Fig. 7.7 Re-connection Confirm

Pagina 29 - 7. Monitoring

30 8. Version Information Fig. 8.1 Version Information [1] Application version The version of this application is show

Pagina 30 - 7-2 Controller Error List

31 9. File Extensions Table 2 List of File Extensions Model name Position data file Parameter file Backup file RCP *.ptr *.pmr *.bkr RCS

Pagina 31

32Change History noisiveR fo noitpircseD etaD noisiveRAugust 20119th edition Change in software license agreement.

Pagina 32

Manual No.: ME0107-9A (August 2011)The information contained in this document is subject to change without notice for purposes of product improvement.

Pagina 33

A Word of Caution [1] This software is copyrighted by IAI Corporation (IAI). [2] The software and the manual can only be used upon the software lice

Pagina 34

Table of Contents 1. Before You Begin ...

Pagina 35 - 8. Version Information

1 1. Before You Begin 1-1 Items Supplied with This Software Please check to make sure that the following items are included in your softwar

Pagina 36 - 9. File Extensions

2 [9] Serial port An RS232C serial port. (Only a 9-pin port is supported.) [10] Printer A printer compatible with the PC. 1-3 Installing the

Pagina 37 - Change History

3 1-5 Setting of Application Window The “Setting of application” window (Fig. 1) is displayed only once after the software has been installed f

Pagina 38 - 11.08.000

4 2. Checking for Connected Axes The software checks for connection all axes up to the axis specified in the Last axis # box of the “Setting of

Comentarios a estos manuales

Sin comentarios