Iai-america RCS-C Manual de usuario Pagina 103
- Pagina / 119
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix
93
Appendix
7.4 Alarms, Causes and Actions
(1) Message Alarms
Code Error Cause/action
040 Emergency stop Cause: An emergency stop status was detected.
(This is not an error.)
05A Receive overrun
05B Receive framing error
05C Receive timeout error
05D Header error
05E Delimiter error
07F BCC error
An error occurred during operation using the PC software/teaching
pendant or serial communication via PLC’s communication module.
Cause: [1] Garbage data due to noise
[2] Duplicate slave numbers when multiple actuators are
controlled via serial communication
Action: [1] Revise the wiring, equipment layout, etc., to eliminate
noise.
[2] Change the slave numbers to eliminate duplication.
061 FNCCHR W address error
062 Operand 1 error
063 Operand 2 error
064 Operand 3 error
An error occurred during serial communication via the PLC’s
communication module.
Cause: An undefined command or out-of-range data was received.
Action: Review the data sent and correct the format.
065 EEPROM write timeout Cause: Writing of parameter or position data to the nonvolatile memory
does not complete within 200 ms.
(This alarm does not occur during normal operation.)
Action: Do not issue a PLC command and write data using the
PC/teaching pendant at the same time.
070 Movement command at RUN-OFF Cause: A movement command was issued when the servo was OFF.
Action: Before issuing a movement command, confirm that the servo is
ON (the position complete signal is ON).
071 PTP before homing completion Cause: A movement command was issued to the absolute actuator via
serial communication when the home position was not yet
established.
Action: Perform an absolute reset to establish the home position first.
(Refer to 4-2, “Absolute Reset Procedure.”)
073 Error reset at servo ON Cause: An alarm reset command was issued while the actuator was
operating via serial communication with the servo ON.
(This alarm does not cover PIO commands.)
Action: Before issuing an alarm reset command, confirm that the servo
is OFF.
075 Movement command during homing Cause: The next movement command was issued in the middle of
homing.
Action: Issue the next movement command after homing has
completed.
07A ABS battery voltage low Cause: The battery voltage was 3.2 V or below when the power was
input.
Action: Replace the battery as soon as possible.
- RCS Series 1
- ROBO Cylinder Controller 1
- RCS-C Type 1
- CAUTION 2
- Warning 3
- Caution 3
- Before Use 7
- Table of Contents 8
- Absolute Specification 11
- 1. Overview 11
- 1.3 Safety Precautions 13
- 1.5.2 Power Supply 15
- 2.1 Basic Specifications 19
- 2.2.1 Names 21
- 2.2.2 Functions 21
- 2.3.2 Absolute Specification 27
- 2.4 Connection Method 28
- 2.5 Supplied Cable 30
- 2.5.2 Motor Extension Cable 31
- 2.6 Wiring 32
- Home return completion 33
- 2.6.3 PIO Interface 34
- Command position 1 36
- Command position 2 36
- Command position 4 36
- Pin No 36
- Command position 8 36
- Input Part 37
- Output Part 38
- 3.1 Base Specification 39
- 3.2.1 Names 42
- 3.2.2 Functions 42
- 3.3 External Dimensions 48
- 3.3.2 Absolute Specification 49
- 3.4 Connection Method 50
- Battery 51
- 3.5 Supplied Cables 52
- 3.5.2 Motor Extension Cable 53
- 3.6 Wiring 54
- Emergency stop 55
- 3.6.3 PIO Interface 56
- Rectifier 59
- Each output 60
- [A] Push = 0 63
- [B] Push = Other than 0 63
- 4.2 Explanation of Modes 66
- Positioning 68
- 4.2.5 Pause 69
- 4.2.6 Zone Signal Output 69
- 4.3 Timing Chart 70
- 1 msec or less 76
- 5.5 Push & Hold Mode 79
- Moving output ON 83
- 0.1 mm before position 1 83
- 5.8 Pause 85
- 4 msec or less 86
- 4 msec or more 86
- 5.9 Zone Signal Output 87
- 5.10 Returning Home 89
- Position 0 90
- 5.11 Incremental Moves 91
- 6. Parameters 95
- 6.3 Parameter Settings 96
- Movement flag during stop 99
- 6.3.3 Servo Gain Adjustment 100
- 7. Troubleshooting 101
- 7.3 Alarm Output by PIO 102
- (1) Message Alarms 103
- (3) Cold Start Alarms 106
- * Appendix 111
- (Total of both fingers) 112
- Distance from point of action 113
- Point of action 113
- Position Table Record 117
- Parameter Record 118
- IAI (Shanghai) Co., Ltd 119
Relacionado con productos y manuales para Hardware Iai-america RCS-C
Hardware Iai-america E-Con Manual de usuario
(111 paginas)
(111 paginas)
Hardware Iai-america XSEL Ethernet Manual de usuario
(60 paginas)
(60 paginas)
Hardware Iai-america PS-24 Manual de usuario
(32 paginas)
(32 paginas)
Hardware Iai-america PCON-ABU Manual de usuario
(60 paginas)
(60 paginas)
Hardware Iai-america IA-IO-3205-PN Manual de usuario
(14 paginas)
(14 paginas)
Hardware Iai-america TU-MA96-P Manual de usuario
(15 paginas)
(15 paginas)
Hardware Iai-america REXT Manual de usuario
(443 paginas)
(443 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales