Iai-america RCS-C Manual de usuario Pagina 109
- Pagina / 119
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix
99
Appendix
7.5 Messages Displayed during Operations Using Teaching Pendant or PC Software
The warning messages that may be displayed during operations using the teaching pendant or PC software are
explained below.
Code Message Description
112 Input data error An inappropriate value was input as a user parameter setting.
(Example) “9601” was input as the serial communication speed by
mistake.
Input an appropriate value again.
113
114
Input value too small
Input value too large
The input value is under the setting range.
The input value is over the setting range.
Input an appropriate value again by referring to the actuator
specifications and parameter list.
115 Homing not yet complete The current position was written before homing was complete.
Perform homing first.
116 Last position data available When new data is added, data already exists in the last position of the
position table.
Clear or delete the data in the last position first.
117 No movement data No target position is set under the selected position number.
Input a target position first.
11E Inconsistent data pair The magnitude relationship of a pair of data is inappropriate.
(Example) The same value is set in both the + and – soft limit
parameters.
Input appropriate values again.
11F Absolute value too small The minimum travel toward a target position is determined by the lead of
the drive system and encoder resolution.
This message indicates that the input target position is less than this
minimum travel.
(Example) With the RCS-R30, the lead is 90 and encoder resolution is
3,072 pulses. Therefore, the minimum travel is calculated as
0.029/pulses (90 3,072).
If “0.02 is input as the target position, this message will be
displayed.
121 Push search end over The final position in push-motion operation exceeds a soft limit.
No harm is done as long as the actuator contacts the work part. If it
misses the work part, however, the actuator will reach the soft limit and
this message will be displayed.
Change either the target position or positioning band.
122 Multiple axes connected at assignment An axis number was assigned when multiple axes were connected.
Always assign an axis number when only one axis is connected.
180
181
182
Axis number change OK
Controller initialization OK
Home change all clear
This is an operation check message.
(It does not indicate misoperation or error.)
201 Emergency stop An emergency stop was actuated. (This is not an error.)
20A Servo OFF during movement The servo ON signal (SON) was turned OFF by the PLC while the
actuator was moving. As a result, the servo turned OFF and the actuator
stopped.
- RCS Series 1
- ROBO Cylinder Controller 1
- RCS-C Type 1
- CAUTION 2
- Warning 3
- Caution 3
- Before Use 7
- Table of Contents 8
- Absolute Specification 11
- 1. Overview 11
- 1.3 Safety Precautions 13
- 1.5.2 Power Supply 15
- 2.1 Basic Specifications 19
- 2.2.1 Names 21
- 2.2.2 Functions 21
- 2.3.2 Absolute Specification 27
- 2.4 Connection Method 28
- 2.5 Supplied Cable 30
- 2.5.2 Motor Extension Cable 31
- 2.6 Wiring 32
- Home return completion 33
- 2.6.3 PIO Interface 34
- Command position 1 36
- Command position 2 36
- Command position 4 36
- Pin No 36
- Command position 8 36
- Input Part 37
- Output Part 38
- 3.1 Base Specification 39
- 3.2.1 Names 42
- 3.2.2 Functions 42
- 3.3 External Dimensions 48
- 3.3.2 Absolute Specification 49
- 3.4 Connection Method 50
- Battery 51
- 3.5 Supplied Cables 52
- 3.5.2 Motor Extension Cable 53
- 3.6 Wiring 54
- Emergency stop 55
- 3.6.3 PIO Interface 56
- Rectifier 59
- Each output 60
- [A] Push = 0 63
- [B] Push = Other than 0 63
- 4.2 Explanation of Modes 66
- Positioning 68
- 4.2.5 Pause 69
- 4.2.6 Zone Signal Output 69
- 4.3 Timing Chart 70
- 1 msec or less 76
- 5.5 Push & Hold Mode 79
- Moving output ON 83
- 0.1 mm before position 1 83
- 5.8 Pause 85
- 4 msec or less 86
- 4 msec or more 86
- 5.9 Zone Signal Output 87
- 5.10 Returning Home 89
- Position 0 90
- 5.11 Incremental Moves 91
- 6. Parameters 95
- 6.3 Parameter Settings 96
- Movement flag during stop 99
- 6.3.3 Servo Gain Adjustment 100
- 7. Troubleshooting 101
- 7.3 Alarm Output by PIO 102
- (1) Message Alarms 103
- (3) Cold Start Alarms 106
- * Appendix 111
- (Total of both fingers) 112
- Distance from point of action 113
- Point of action 113
- Position Table Record 117
- Parameter Record 118
- IAI (Shanghai) Co., Ltd 119
Relacionado con productos y manuales para Hardware Iai-america RCS-C
Hardware Iai-america E-Con Manual de usuario
(111 paginas)
(111 paginas)
Hardware Iai-america XSEL Ethernet Manual de usuario
(60 paginas)
(60 paginas)
Hardware Iai-america PS-24 Manual de usuario
(32 paginas)
(32 paginas)
Hardware Iai-america PCON-ABU Manual de usuario
(60 paginas)
(60 paginas)
Hardware Iai-america IA-IO-3205-PN Manual de usuario
(14 paginas)
(14 paginas)
Hardware Iai-america TU-MA96-P Manual de usuario
(15 paginas)
(15 paginas)
Hardware Iai-america REXT Manual de usuario
(443 paginas)
(443 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.098 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales